Mainly used for structural construction without the use of stucco, or for decorative coverage, interlocking deck tiles can be placed on existing surfaces such as concrete, stone, brick, or even wood decks. Interlocking deck tiles are very durable and skid resistant. Next, Jiabang interlocking deck tile manufacturer will introduce the purchasing skills of interlocking deck tiles.

How to buy interlocking deck tiles

1. The color selection of interlocking deck tiles: When choosing the color of the wall, it should be in harmony with the indoor environment. It is generally not recommended to use white or too light colored decorative tiles, which can avoid the lack of texture of the wall; In the meantime, of wall brick and floor tile tonal also should mutual form a complete set, and toilet ceramic tile should be provided with clean give priority to, wall floor tile and all sorts of fittings include hardware and the quality of material of form a complete set, class keep harmonious and consistent.

2. The choice of durability: after interlocking deck tiles are laid, there will be no cracking, deformation and pollution absorption for a long time. We can judge it in the following ways:

A. You can use ink drops on the back of the tiles to see if the ink spreads automatically. The slower the spreading speed, the better the quality of the interlocking deck tiles and the better the durability of the interlocking deck tiles; The opposite is worse.

What is the standard that ceramic tile shop sticks?

1. Soak water as needed when laying ceramic tiles

The ceramic tile that bubble passes water affects sells 2 times, manufacturer businessman cannot return commonly change, can make unnecessary waste. Advice; To combine the construction progress of workers, need to use how much to run how much, avoid waste.

2. Make a plan to beat tiles before tile laying

A lot of construction workers get bricks on the shop, such as the shop to a certain extent, only to find that the proportion is not coordinated, had to tear down the shop again, causing unnecessary waste. Suggestion: Make a tiling plan before tiling.

3. Remind workers to timely notice the problems of ceramic tile quality found in the construction process

A lot of friends are always in the shop after the paste is found to have a problem, and then the construction side and the material side to elude each other, causing unnecessary disputes, advice: in the construction to clearly tell the workers, once found ceramic tile problems timely notice, so as to avoid unnecessary disputes.

4. Proper mixing of cement and sand

The proportion of cement is large, and the brick can be quickly adhered to, but the expansion coefficient of cement mortar is large, and it is easy to crack the brick after paving. Suggestion: the mixing ratio of cement sand wall brick is 1:3, floor tile is 1:2.

5. Be careful when working tiles

When re-laying the wall in the touch of the sun Angle, the edge grinding should be careful, do not destroy the glaze layer of the ceramic tile, pay attention to the gap can not be too small when connecting, some ceramic tiles that need to be cut can best be cut at the time of purchase after the material supplier in the delivery.

6. When dealing with the flue, the wall must be treated in a standard way

Rebuild the wall can not use large core board to do wall material, tiling is easy to cause tile arch, fall off and cracking.

7. Ceramic tile seam should not be too small

Ceramic tile seam is too small to reduce the service life of ceramic tiles, ceramic tiles after thermal expansion and cold contraction crack the glaze. Suggestion: whether there is a seam tile or seamless tile, pay attention to the gap in the construction, it is best to ask the material supplier how much gap needs to be left when buying.

8. Seam filling should be carried out after the ceramic tiles are dry and solid

The ceramic tile is not completely dry, immediately caulking easy to cause the loose ceramic tile, and even lead to the later ceramic tile fall off, leaving hidden dangers. Suggestion: tick off sew to need to undertake again after ceramic tile dry solid, undertake after 24 hours commonly.

9. Protect the tiles when you're tiling them

Do not scratch, pollute the brick surface, do wall paint, paint do not walk on the brick surface without dry, otherwise it will cause damage to the ceramic tile.

The construction craft of ceramic tile

1. The standard procedure of floor tile paving is: cleaning and finishing the basic floor → cement mortar leveling → calibration height, elastic line → installation of standard block → material selection → infiltration → paving → filling seam → cleaning → maintenance and delivery.

2 Old house ground must be fully hair, concave depth is not less than 0.5 mm, spacing 5 CMS, and then brush the water purification mud. Attention can not collect water, to prevent through the plate seam seepage to the downstairs.

3. For those with drainage slope requirements, such as toilet, bath room, etc., the slope direction of tiling should be controlled by pulling lines according to the corresponding slope.

4. Base acceptance: the surface leveling shall be checked by 2m ruler, the deviation shall not be more than 5mm, and the elevation deviation shall not be more than ±8mm.

5 stone, floor tile varieties, specifications, color and pattern should meet the requirements of the design, residents, decorative panel surface shall not have scratches, lack of edge drop corners and other quality defects. Do not use expired and caked cement as binder. Floor tiles must be all out of the box before the selection.

6. The floor tiles should be carefully measured before pasting, as far as possible with computer typesetting, and choose a reasonable plan, statistics out the number of specific floor tiles, in order to arrange beautiful and reduce loss for the purpose, and focus on checking whether the geometric size of the room is neat.

7 mortar use 1:2.5 cement mortar volume ratio (specific often grip as: hand holding group, floor-to-flower), the bonding layer shall not be less than 12㎜ thick, full mortar, cement unified use of big factory cement. 800×800 polished brick or granite adopts 1:4 ~ 1:6 cement mortar volume ratio. Floor tiles above 600×600 (including 600×600) and above 500X500 specifications should be dry paste method. Light colored granite, marble application white cement hanging brush slurry, in case of color.

8. The floor tiles should be soaked and dried before paving, and then dry and wet, with no water mark on the surface, and use color selection.

9. Before laying and pasting, we should pull the crosshaires in the horizontal and vertical directions. When laying and pasting, we must ensure that the crosshaires are connected and no staggered joints shall be allowed.

10. When laying floor tiles, follow the shop to keep clean and clean at any time. (clean with cotton yarn or sawdust), and the cement mortar in the brick seam is cleaned, and the seam is pointed after completion

11 pointing before completion, first clear the seam, with white cement and talcum powder putty, pointing putty is lower than 1㎜ brick surface.

12. When paving the floor tiles, other types of work shall not be polluted or trampled. After the completion of the floor tiles, the joints should be cleared within 24 hours, and the maintenance should be done. In order not to affect the construction of other projects, solid boards can be laid on the ground for people to walk.

13. After the floor tiles are laid, cover and protect them with thick cardboard after checking that there is no flatness error, empty drum and color difference. The nails on the cardboard must be removed, and sealing glue must be used between the cardboard and the cardboard to prevent sundries from entering.

14. It is strictly prohibited to use water without drainage or water storage equipment, especially to prevent soaking the cardboard used to protect the floor tiles, so as to prevent indirect pollution of the floor tiles.

15. Filling foundations such as flower pond and toilet are filled with moistened concrete and carbon slag, which is dense, reliable and light in weight, and has no potential safety hazard in bearing.

16. Stone or ceramic tile baseboard can be flush with the wall facade according to customer requirements, so that the construction does not accumulate dust, easy to clean and sanitary, good for furniture display.

For more information about interlocking deck tiles, please contact Jiabang interlocking deck tiles manufacturer.